Manor, TX

Today I arrived and met with Tom & his wife. I completed the fall evaluation of the homes HVAC system. I turned on heating and tested all functions of performance and tested the safeties. System performs well and is safe. I also washed the outdoor unit using water and treated the electrical compartment using electrical insecticide. I gave customer bacteria prevention options and at this time they are considering HH14C. Please email my estimate to them, they will talk over more seriously and call in with approval. Upon departure the system is left in cooling mode set to 76 currently 74 inside.

Today i arrived and met with the homeowners. I completed the fall hvac evaluation at this time. During evaluation I tested heating system performance and found it performing well, all safeties are intact and working. I flushed water removal system while in attic and changed filter provided by customer. I also washed outdoor unit using water and verified all is in working order for heating season. Upon departure I left the system control set to 80 in cooling mode.

Upon my arrival I spoke with the customer about his concerns on the hvac system freezing over. I performed a diagnostics on the system, checked the amp draws, temperature split, pressures and air flow of the system. I found that the air movement system kept surging while I performing the diagnostics. Upon further inspection I found that the air movement system is faulted. Spoke with the customer about his different options for repair and he chose to go with HC6E. We will need to schedule a return date to perform the repair and customer would also like window units if the repair can’t be done soon.

Upon our arrival in Manor we recovered all of the refrigerant, removed the faulted refrigerant pressure control and installed the new one. Installed new inline filter dryer then purge and pressure tested the system with nitrogen. During the pressure test we found that the gasket that came with the refrigerant pressure control was not sealing properly. Evacuated the nitrogen, installed a new gasket and added nitrogen back to the system for another pressure test. Insured that the gasket was sealed proper and continued with the timed pressure test. Found the pressure test to be good, evacuated the nitrogen and put the system into a vacuum. Once system came down to below 500 microns we added 8 pounds of clean R410a refrigerant. Installed a new voltage enhancement system and redid the wire terminals. Turned the system on for the performance and safety testing, found everything to be operating properly at this time.

WO-TNFR352863 upon my arrival in Manor I found that the main refrigerant control valve was not operating properly gave customer options he choose HI2C. Part have been ordered .

Performed cooling evaluation in Manor, system operations were good, but did let customer know about concern of bacteria inside air handler recommends Ultra Violet bacteria prevention to improve indoor air quality will get with wife and call later with which options to pick please transfer tnfr’s .

Upon my arrival performed a heating evaluation and found that system is working good at this time. Did let customer know it was time to renew but they said they wanted to renew in may.

Upon my arrival I found that the zoned closet unit was not coming on. Checked for proper voltages at the system, the zone board and the thermostat. I had proper voltage coming into the zoning board but did not have the proper voltage coming out of the board to the equipment. Found the manual for the zone board in the closet and went through and made sure everything was wired in properly and the settings were set properly. Everything was set up the correct way. All this points towards the zone board being faulted. Spoke with the customer about their different options and they would like the quotes emailed over so they can look them over and follow up with the insurance to see if they are going to cover the repair or if they will have to cover it. Client also wants quotes sent over separately on surge protection in case they do not go with one of the top options that add surge protection to the system. I updated the email and phone number on file. The correct email to send everything to

Performed the heating evaluation and found everything to be operating properly at this time.

Performed maintenance on system, found all units and components running and operating properly.

Upon my arrival to Manor, Tx., I found that the ac system was not turning on found that ac system was wired incorrectly, and kept popping the fuse. Made repairs to wiring and found system was low on refrigerant, customer said previous company was not able to get system to run, did not see any leaks , added 2 pound of refrigerant. Left equipment running at this time.

When I arrived I found that the outdoor unit for the 3 zone system was not operating. There were no visible fault codes on the condenser. I then reset the system and it came on. I checked the operation of the system and found it cooling properly. When I connected to the indoor u it it stated. There had been several communication faults but did not say a date. I let the client know if this keeps happening we will have to replace the wire from the indoor to the outdoor and place in conduit because it is a communicating system. I also recommend maintenance for all 3 systems.

Upon my arrival performed a cooling evaluation found no issues at this time.

Upon my arrival to Manor, Tx., I performed a cooling evaluation found ac unit to be working properly at this time.

I performed the fall evaluation on the closet heat pump system and found it operating properly. The clue came apart in the drain line so I fixed it.

Arrived for the AC system service. I performed the heating evaluation on the air conditioning system and found a bad voltage distribution system and a dirty coil on one of wall mounted units and bad voltage enhancement system on the unit in the main house, spoke with client about his options and he went with HN13A repair and HD3A repair, I replaced the voltage enhancement system and the voltage distribution system and the systems are operating at manufacturer specifications at this time, client asked if I send him a quote for the cleaning.

Arrived for the AC system service. I performed the heating evaluation on the air conditioning system and found a bad voltage distribution system and a dirty coil on one of wall mounted units and bad voltage enhancement system on the unit in the main house, spoke with client about his options and he went with HN13A repair and HD3A repair, I replaced the voltage enhancement system and the voltage distribution system and the systems are operating at manufacturer specifications at this time, client asked if I send him a quote for the cleaning.

Arrived for the AC system service. I performed the heating evaluation on the air conditioning system and found a bad voltage distribution system and a dirty coil on one of wall mounted units and bad voltage enhancement system on the unit in the main house, spoke with client about his options and he went with HN13A repair and HD3A repair, I replaced the voltage enhancement system and the voltage distribution system and the systems are operating at manufacturer specifications at this time, client asked if I send him a quote for the cleaning.

Arrived for the AC system service. I performed the heating evaluation on the air conditioning system and found a bad voltage distribution system and a dirty coil on one of wall mounted units and bad voltage enhancement system on the unit in the main house, spoke with client about his options and he went with HN13A repair and HD3A repair, I replaced the voltage enhancement system and the voltage distribution system and the systems are operating at manufacturer specifications at this time, client asked if I send him a quote for the cleaning.

Arrived for the AC system repair. I found the voltage enhancement system dead, spoke with client about her options and she went with HN14C repair at this time.

Arrived for the AC system repair. I found the voltage enhancement system dead, spoke with client about her options and she went with HN14C repair at this time.

Arrived for the AC system repair. I found the voltage enhancement system dead, spoke with client about her options and she went with HN14C repair at this time.

Arrived for the AC system repair. I found the voltage enhancement system dead, spoke with client about her options and she went with HN14C repair at this time.

I performed the cooling evaluation on the air conditioning system and the system is operating at manufacturer specifications at this time I added a little bit more duct sealant were the Reme Halo is at everything is operating properly.

I performed the cooling evaluation on the air conditioning system and the system is operating at manufacturer specifications at this time I added a little bit more duct sealant were the Reme Halo is at everything is operating properly.