Rosanky, TX

Today I arrived in Rosanky. I evaluated the hvac system, I verified the heating system is operational and is safe. When evaluating performance the system only has a temp difference of 9 degrees I further found that the auxiliary heating system has 1/3 of the section had. I recommended either replacement of the auxiliary heating system or consult on upgraded unit. Upon departure system is left in heating mode set for 73 currently 77 inside.

Upon my arrival in Rosanky I performed the heating evaluation on the heat pump system. I found everything at the air handler operating properly. Moving to the outdoor condenser I found the voltage distribution system is getting chard/pitted. I spoke with the customer about their different options for repair and they would like them emailed over so they can talk it over. I also spoke with the customer about how his HVAC system performed this past summer given its age. They said they didn’t notice any issues with the system and that everything cooled great. I did go over the newer equipment that is coming out and the benefits a newer system has. The customer didn’t want to move forward with anything on that at this time but will keep it in mind when a major repair presents itself with the system.

Performed the cooling evaluation in Rosanky on both system. System number 2 the Reme halo was not coming on. I found that the voltage conversion system was faulted. I replaced the voltage conversion system under the warranty from when the Reme halo was installed since it was the one that came with the Reme halo. Turned the system on and found it working properly. I found that both systems are low on refrigerant indicating a leak on the system. I spoke with the customers about my findings and recommended having a comfort specialist come out and quote a system replacement on both units. They would like an appointment set up for the comfort specialist to come out and go over the quotes. When the comfort specialist comes out they are going to ask about having the 2 systems combined into 1.

Upon my arrival in Rosanky I performed a cooling evaluation on 2 systems, found that the downstairs system was run while in construction and has a very dirty coil. Recommend cleaning on this time and a safely switch and p-trap be installed. On the upstairs system customer wants the drain line fixed to go out to the vent pipe or outside to the house. The air flow is so much you can hear it, customer wants an added to the stair case since it get hot there this would help with the noise in the bed room.

Upon my arrival in Rosanky I found that the voltage enhancement system was extremely low. Spoke with the customer about replacing the voltage enhancement system and they chose to move forward. After the repair I found that the refrigerant pressure control was faulted over loading the compressor with refrigerant and causing a higher then normal sub cool. Spoke with the customer about their different options for repair and they chose to go with HI2D. Will work on getting the parts ordered and a materials list together for the return. Customer would like some window units to keep them cooling until the repair can be performed. They also signed up for our maintenance. Heat pump closet system.

Upon my arrival in Rosanky I found that the main control board on the outdoor system is faulted causing the system to have error code E1. Spoke with the customer about his different options for repair and he chose to go with HE19A. Customer also signed up for the maintenance program. It will be a couple of weeks until he is able to return back for the repair to be performed. He would also like the first evaluation to be heating and do the cooling closer to summer next year. Repair will take 1 tech 1 hour to perform.

Upon my arrival in Rosanky, I found that the fuse was blown on the master bedroom A/C system. Put my inline fuse popper on the system and found that the voltage conversion system was faulted, spoke with the customer about doing the repair in order to trace down where the short is coming from that faulted the transformer. Found that one of the thermostat stat wires was shorted causing the system to malfunction. After fixing the short I tested pressures and found that the system was extremely low on R22 refrigerant. I turned the condenser off at the breaker and left the air handler on so the fan can still run to at least move air. Spoke with the customer about the leak and he would like to have quotes sent over to replace the master bedroom system then would also like a quote put together to replace both systems. Will need to set a day for Daryl to come out and do a consultation.

Upon my arrival in Rosanky, I performed HK11D. Chemically cleaned the air movement system and heat transfer media coil, redid wire terminals, installed new voltage enhancement on the indoor air movement system, cleaned the inside of the air handler, sprayed system with bio protect, cleared the water removal system and tested the system.

Upon my arrival in Rosanky, I performed the A/C cooling evaluation and found everything operating properly at this time. During the evaluation I found the indoor air movement system was dirty. Spoke with the customer about her different options for repair and they chose to go with HK11D. Will need to schedule a return date to perform the cleaning. Will take 1 tech 1.5-2 hours to complete, will also need to make sure to bring plastic to cover the heat strips for the heat transfer media coil cleaning being it is a down flow system. Paid in full.

Upon my arrival in Rosanky, I started on repairs HK12A on the A/C unit pull and clean , I was not able to bring down the indoor heat exchanger, switched cleaning to hk2C. Removed air movement system and cleaned it out side, clean the indoor heat transfer system in place, installed a performance enhancement system. Put system all back together and checked operations, pressure tested system it head and performed a vacuum on it. System is working properly at this time.

Performed cooling evaluation on system, I found all components running properly at this time. I found bacterial growth inside indoor system, showed client the pictures and client asked for estimates be sent over to them via email for cleaning and Reme Halo uv air purification system.

Performed cooling evaluation on system, found all components running and operating properly at this time.

Upon my arrival I performed HH14E. I pulled and chemically cleaned the air movement system. Chemically cleaned the heat transfer media coil and the cabinet. Cleaned the outside of both air handlers. Resealed both plenums and moved a 7 inch duct to allow for better air flow to the back room. Installed Reme halo with the air switch and sealed around it. Sprayed the coil with bio fresh and turned the fan on to circulate bio protect through the house hold. Tested the system and made sure it everything was operating properly.

Upon my arrival performed a heating evaluation on 2 electric furnaces. Found that the equipment is working good at this time.

Performed the heating evaluation on both systems and found everything to be operating properly at this time. During the evaluation I found that system 2’s heat transfer media coil and air movement systems are dirty. I spoke with the customer about the cleaning and Reme halo. They chose to go with HH14E. This will include the cleaning they need. We will be installing the Reme halo on system 2. When we return to instal the Reme halo we will need the pressure washer, viper cleaner, bio protect, vaporizer, mastic, Reme halo, air switch, 5/32 hose around 4’, and some thermostat wire. We will reseal around both plenums, put bio protect in the vaporizer and flow it through the duct system, wire in Reme halo with air switch, move a seven inch duct for better air flow, pull and clean the air movement system and wash the heat transfer media coil. 1 tech 3-4 hours. I would like to do the return if possible.

Performed heating evaluation on system. Found all components running and operating properly at this time.

Upon arrival in Rosanky TX Performed the heating evaluation and found everything to be operating properly at this time.

Performed heating evaluation on system, found all components running and operating properly at this time.

Performed repairs in attic heat pump system. Replaced the indoor air movement system, the wiring harness, and the main circuit control board in system. Ran airflow verification test to ensure all was running properly at this time after repairs. Informed client about the urgency for surge protection once again. All running properly at this time after repairs were performed.

Performed maintenance on both systems, found all units and components running and operating properly at this time.

Performed maintenance on system, found units and all components running and operating properly at this time.

Upon my arrival to Rosanky, Tx., I performed maintenance on both complete ac systems. Found all ac units and components running properly and performing within manufacturer specifications. Found surge protectors on #1 bad, client chose not to replace component at this time.

Upon my arrival to Rosanky, Tx., I performed maintenance on both ac systems. Found both ac units and all components running properly and performing within manufacturer specifications.

Upon my arrival in rosanky, tx., i replaced circuit control board and wiring hardness tested equipment and found that ac system is now working good. Still did not find what could have caused last board to go bad. Left equipment running. Did not use blower motor will need to return it.

Upon my arrival found that the indoor circuit board went bad, could not find anything that would lead me to think it on a reason why is went bad, will need to reorder the parts and come back to install them.